Venstar ACC0431 Spezifikationen PDF herunterladen (Seite 32)

5 3 D S --- 9 0 0 --- --- --- 0 7 0

5 3 D S --- 9 0 0 --- --- --- 0 7 1

5 3 D S --- 9 0 0 --- --- --- 0 8 7

5 3 D S --- 9 0 0 --- --- --- 0 8 8

Installation Instructions

Du ct---F r ee Sys tem s

Cooling Only and Heat Pump Units (Size 018---060)

Acces so ry Wind Ba ffl e Kit

2To5NominalTons

NOTE: Read and become familiar with these instructions before

beginning installation.

SAFETY CONSIDERATIONS

Installing and servicing air--conditioning equipment can be

hazardous due to system pressures and electrical components. Only

trained and qualified personnel should install or service

air-- conditioning equipment. When working on air-- conditioning

equipment, observe the precautions provided in literature, tags, and

labels attached to the unit.

Follow all safety codes. Wear safety glasses, protective clothing,

and work gloves. Use quenching cloth for brazing operations.

Have fire extinguisher available. Read these instructions

thoroughly and follow all warnings or cautions included in

literature and attached to the unit. Consult local building codes and

National Electrical Code (NEC), ANSI/NFPA 70, Canadian

Electrical Code CSA C22.1 and local codes and ordinances for

special requirements.

Recognize safety information. This is the safety--alert symbol

When you see this symbol on the unit and in instructions or

manuals, be alert to the potential for personal injury.

Understand these signal words: DANGER, WARNING, and

CAUTION. These words are used with the safety--alert symbol.

DANGER identifies the most serious hazards which will result in

severe personal injury or death. WARNING signifies hazards

which could result in personal injury o r death. CAUTION is used

to identify unsafe practices which may result in minor personal

injury or product and property damage. NOTE is used to highlight

suggestions which will result in enhanced installation, reliability, or

operation.

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could result in personal injury

or death.

Before beginning any modification or installation of this kit,

be sure the main electrical disconnect is in the OFF position.

Ensure power is disconnected to the fan coil unit. On some

systems both the fan coil and the outdoor unit may be on the

same disconnect. T ag the disconnect switch with a suitable

warning label. There may be more than one disconnect.

WARNING

GENERAL

These instructions cover the installation of the accessory wind

baffle kit on cooling only, heat pump, and multi--split units. The kit

is used with horizontal discharge outdoor units to provide

improved unit operation in areas with high winds.

INSTALLATION

Refer to Table 1 for kit contents and usage.

UNIT DAMAGE HAZARD

Failure to follow this caution may result in unit damage.

To avoid compressor damage, never turn unit on its side or

top when installing kit components.

CAUTION

STEP 1 —Install Z Brackets

1. Remove existing screw from outdoor unit top cover. See

Fig. 1.

2. Position top Z bracket between grille and top cover. Be sure

shorter top bend of Z bracket slips between top cover flange

and metal strip behind top cover flange. See Fig. 1.

3. Reinstall screw removed in Step 1, inserting it through

screw hole in top cover and Z bracket. Fasten screw into

grille.

4. Install bottom Z bracket in basepan corner, following same

procedures. Be sure shorter top bend of Z bracket slips

between basepan flange and metal strip behind basepan

flange. See Fig. 1.

STEP 2 —Join End and Front Baffles

1. Using the screws provided in kit, join the 2 baffles at their

center holes. See Fig. 2. Tighten screws securely .

STEP 3 —Attach End Baffle Flange

1. Remove 3 screws from coil cap. See Fig. 1.

2. Install end baffle flange to Z bracket and use 3 screws re-

moved in Step 1 to secure one end. See Fig. 1 and 2. End

baffle flange fits against coil cap. Tighten screws snugly. Do

not overtighten.

STEP 4 —Attach Front Baffle Flange

1. Remove 2 screws from access panel. See Fig. 1.

2. Install front baffle flange using 2 screws removed in Step 1.

Front baffle flange overlaps end baffle flange where Z

brackets are installed. With baffle in place, tighten all screws

snugly. Do not overtighten.

1 2 ... 27 28 29 30 31 32 33 34 35 36 37

Kommentare zu diesen Handbüchern

Keine Kommentare

Venstar ACC0431 Spezifikationen Seite 32

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Fernbedienungen Venstar ACC0431